表面处理对激光选区熔化成型纯钛钛瓷结合强度的影响

doi:10.19439/j.sjos.2023.03.002

摘要/Abstract

摘要： 目的：探讨表面处理对激光选区熔化（selective laser melting,SLM）成型纯钛钛瓷结合强度的影响。方法：采用SLM技术制作纯钛条64个,钴铬合金条16个（25.0 mm×3.0 mm×0.5 mm）。根据喷砂压力及中间层将纯钛试件分为4组,TB1组为0.25 MPa喷砂的粘接瓷组,TG1组为0.25 MPa喷砂的金涂层,TB2组为0.45 MPa喷砂的粘接瓷,TG2组为0.45 MPa喷砂的金涂层,各组一半烤瓷试件进行10 000次冷热循环实验（n=8）。以0.25 MPa及0.45 MPa压力喷砂的钴铬合金金瓷结合强度作为对照,记为C1、C2组（n=8）。利用经典三点弯曲实验测试烤瓷试件的金瓷粘接强度,使用激光扫描共聚焦显微镜测量纯钛表面粗糙度,使用场发射扫描电镜观察钛瓷结合界面形貌,使用体视显微镜观察瓷剥脱后钛表面形貌并分析断裂模式,采用Graphpad Prism 8.0软件包对数据进行统计学分析。结果：钛瓷结合强度TG2组（40.16±3.97） MPa显著高于TB2组（36.32±1.44） MPa,TG1组（37.38±2.39） MPa显著高于TB1组（33.75±2.31） MPa（P<0.05）,TB2组显著高于TB1组（P<0.05）。冷热循环后钛瓷结合强度未见明显下降。喷砂压力从0.25 MPa增加至0.45 MPa时,钛表面粗糙度随之显著增加（P<0.05）。纯钛组断裂模式均为混合断裂。结论：本实验条件下,与粘接瓷相比,金涂层可显著提高Ti22瓷粉与SLM纯钛的结合强度,增加喷砂压力可进一步改善钛瓷结合。冷热循环10 000次后,钛瓷结合强度未见显著降低。

关键词: 激光选区熔化, 钛, 钴铬合金, 金涂层, 结合强度, 冷热循环

Abstract: PURPOSE: To evaluate the effect of surface treatment on bonding strength between pure titanium formed by selective laser melting and porcelain. METHODS: Pure titanium strips (64) and cobalt-chromium alloy strips (16) were laser machined to meet ISO 9693 standards. The pure titanium specimens were divided into 4 groups according to the sandblasting pressure and interlayer material. The sandblasting pressure of 0.25 MPa of bonder porcelain group was TB1, the sandblasting pressure of 0.25 MPa of gold coating group was TG1, the sandblasting pressure of 0.45 MPa of bonder porcelain group was TB2, and the sandblasting pressure of 0.45 MPa of the gold coating group was TG2(n=16). After porcelain fusing, half of the specimens in each group were tested for three-point bend bonding strength, and the other half were tested after 10 000 cycles of thermal cycling(n=8). The bonding strength of cobalt-chromium alloy after sandblasting at 0.25 MPa and 0.45 MPa was taken as the control group and recorded as group C1, C2(n=8). The bonding strength was tested using classical three-point bending experiment. The surface roughness of pure titanium was measured by laser scanning confocal microscope(LSCM). Field emission scanning electron microscopy(FE-SEM) was used to observe the interface morphology of titanium-ceramic. The surface morphology of titanium after porcelain stripping was observed with stereomicroscope and fracture modes were analyzed by it. Graphpad Prism 8.0 software package was used for statistical analysis of the data. RESULTS: The bonding strength of group TG2 was (40.16±3.97) MPa and (37.38±2.39) MPa of group TG1, which were significantly higher than that of group TB2 (36.32±1.44) MPa and group TB1 (33.75±2.31) MPa (P<0.05). The bonding strength of group TB2 with 0.45 MPa sandblasting was significantly higher than that of group TB1 with 0.25 MPa sandblasting (P<0.05). There was no significant decrease in titanium-ceramic bonding strength before and after thermal cycling. When the sandblasting pressure increased from 0.25 MPa to 0.45 MPa, the roughness increased significantly (P<0.05). The fracture modes were mixed. CONCLUSIONS: Under the conditions of this study, gold coating can significantly improve the bonding strength of Ti22 porcelain and SLM pure titanium than bonder porcelain, and increase of sandblasting pressure can further improve the bonding strength of titanium-porcelain. After 10 000 cycles of thermal cycling, the titanium-porcelain bonding strength did not decrease significantly.

Key words: Selective laser melting, Titanium, Cobalt chromium alloys, Gold coating, Bonding strength, Thermal cycling

中图分类号:

R783.1

胡丹丹, 任灿霞, 骆小平. 表面处理对激光选区熔化成型纯钛钛瓷结合强度的影响[J]. 上海口腔医学, 2023, 32(3): 230-235.

HU Dan-dan, Ren Can-xia, LUO Xiao-ping. Effect of surface treatment on the three-point bend bonding strength between pure titanium fabricated by selective laser melting and porcelain[J]. Shanghai Journal of Stomatology, 2023, 32(3): 230-235.

参考文献

[1] Memari Y, Mohajerfar M, Armin A, et al.Marginal Adaptation of CAD/CAM all-ceramic crowns made by different impression methods: a literature review[J]. J Prosthodont, 2019, 28(2): e536-e544.
[2] Wei W, Yanan Z, Wenbo L, et al.Microstructural characterization, mechanical properties, and corrosion resistance of dental Co-Cr-Mo-W alloys manufactured by selective laser melting[J]. J Mater Eng Preform, 2018, 27(10): 5312-5320.
[3] Tregerman I, Renne W, Kelly A, et al.Evaluation of removable partial denture frameworks fabricated using 3 different techniques[J]. J Prosthet Dent, 2019, 122(4): 390-395.
[4] Xu W, Xiao S, Lu X, et al.Fabrication of commercial pure Ti by selective laser melting using hydride-dehydride titanium powders treated by ball milling[J]. J Mater Sci Technol, 2019, 35(2): 322-327.
[5] Iseri U, Ozkurt Z, Kazazoglu E.Shear bond strengths of veneering porcelain to cast, machined and laser- sintered titanium[J]. Dent Mater J, 2018, 30(3): 274-280.
[6] Antanasova M, Kocjan A, Abram A, et al.Pre-oxidation of selective-laser-melted titanium dental alloy: effects on surface characteristics and porcelain bonding[J]. J Adhes Sci Technol, 2021, 35(19): 2094-2109.
[7] Antanasova M, Kocjan A, Hocevar M, et al.Influence of surface airborne-particle abrasion and bonding agent application on porcelain bonding to titanium dental alloys fabricated by milling and by selective laser melting[J]. J Prosthet Dent, 2020, 123(3): 491-499.
[8] 骆小平, 卫元鑫, 黄皓宁, 等. 激光选区熔化制作口腔修复体纯钛大跨度支架的精度研究[J].中华口腔医学杂志, 2021, 56(7): 646-651.
[9] Karolewska K, Ligaj B, Wirwicki M, et al.Strength analysis of Ti6Al4V titanium alloy produced by the use of additive manufacturing method under static load conditions[J]. J Mater Res Technol, 2019, 9(2): 1365-1379.
[10] Hou Y, Liu B, Liu Y, et al.Ultra-low cost Ti powder for selective laser melting additive manufacturing and superior mechanical properties associated[J]. Opto-Electron Adv, 2019, 2(5): 8-16.
[11] Yang X, Zhang Z, Gu W, et al.Fabrication of ultra-low-cost pure Ti by selective laser melting using the mixed powders of hydride-dehydride titanium powders treated by ball milling and spherical powders[J]. Powder Metall, 2020, 64(1): 1-8.
[12] Dong YP, Tang JC, Wang DW, et al.Additive manufacturing of pure Ti with superior mechanical performance, low cost, and biocompatibility for potential replacement of Ti-6Al-4V[J]. Maters Des, 2020, 196(11): 1-14.
[13] Hong MH, Min BK, Lee DH, et al.Marginal fit of metal-ceramic crowns fabricated by using a casting and two selective laser melting processes before and after ceramic firing[J]. J Prosthet Dent, 2019, 122(5): 478-481.
[14] Moussa H, Jiang W, Alsheghri A, et al.High strength brushite bioceramics obtained by selective regulation of crystal growth with chiral biomolecules[J]. Acta Biomater, 2020, 106(2): 351-359.
[15] Wu J, Xie H, Sadr A, et al.Evaluation of internal fit and marginal adaptation of provisional crowns fabricated with three different techniques[J]. Sensors (Basel), 2021, 21(3): 740-750.
[16] Antanasova M, Kocjan A, Kovac J, et al.Influence of thermo-mechanical cycling on porcelain bonding to cobalt-chromium and titanium dental alloys fabricated by casting, milling, and selective laser melting[J]. J Prosthodont Res, 2018, 62(2): 184-194.
[17] Iseri U, Ozkurt Z, Kazazoglu E.Shear bond strengths of veneering porcelain to cast, machined and laser-sintered titanium[J]. Dent Mater J, 2011, 30(3): 274-280.
[18] Ustun O, Akar T, Kirmali O.Comparative study of laser irradiation versus sandblasting in improving the bond strength of titanium abutments[J]. Photobiomodul Photomed Laser Surg, 2019, 37(8): 465-472.
[19] Golebiowski M, Wolowiec E, Klimek L.Airborne-particle abrasion parameters on the quality of titanium-ceramic bonds[J]. J Prosthet Dent, 2015, 113(5): 453-459.
[20] Miura E, Tabaru T, Liu J, et al.Effect of gold coating on interfacial reaction between dental porcelain and titanium[J]. Mater Trans, 2006, 70(1): 51-58.
[21] Chakmakchi M, Eliades G, Zinelis S.Bonding agents of low fusing cpTi porcelains: elemental and morphological characterization[J]. J Prosthodont Res, 2009, 53(4): 166-171.
[22] 李瑶. 3D打印技术制作烤瓷冠金瓷结合性能的实验研究[D]. 泸州: 西南医科大学, 2017.
[23] Lim HP, Kim JH, Lee KM, et al.Fracture load of titanium crowns coated with gold or titanium nitride and bonded to low-fusing porcelain[J]. J Prosthet Dent, 2011, 105(3):164-170.
[24] 杨明辉. 浅析金合金烤瓷牙的工艺美感与性能优势[J]. 材料保护, 2020, 53(5): 174-175.
[25] Lee KM, Cai Z, Griggs JA, et al.SEM/EDS evaluation of porcelain adherence to gold-coated cast titanium[J]. J Biomed Mater Res Part B Appl Biomater, 2010, 68(2): 165-173.
[26] 张亚丽, 骆小平, 周黎. 涂覆烧结金膏处理对三种钛瓷粉与纯钛结合强度的影响[J].中华口腔医学杂志, 2012, 47(5): 273-276.