锥形束CT对下颌前磨牙髓腔三维重建的精度分析

doi:10.19439/j.sjos.2018.02.007

上海口腔医学 ›› 2018, Vol. 27 ›› Issue (2): 146-149.doi: 10.19439/j.sjos.2018.02.007

锥形束CT对下颌前磨牙髓腔三维重建的精度分析

李骏¹, 潘乙怀¹, 赵瑜¹, 李玲²

1.温州医科大学附属口腔医院牙体牙髓病科,2.儿童口腔科,浙江温州 325027

收稿日期:2017-06-26 修回日期:2017-08-31 出版日期:2018-04-25 发布日期:2018-05-14
通讯作者: 李玲,E-mail: lealyne@163.com
作者简介:李骏（1981-）,男,硕士,主治医师,E-mail: endo_lijun@aliyun.com
基金资助:
温州市科技计划项目（Y20140333）

Accuracy of 3D reconstruction of pulp cavity in mandibular premolars based on cone-beam CT

LI Jun¹, PAN Yi-huai¹, ZHAO Yu¹, LI Ling²

1.Department of Endodontics, 2.Department of Pediatric Dentistry, School and Hospital of Stomatology, Wenzhou Medical University. Wenzhou 325027, Zhejiang Province, China

Received:2017-06-26 Revised:2017-08-31 Online:2018-04-25 Published:2018-05-14

摘要/Abstract

摘要： 目的:评价锥形束CT（cone-beam CT, CBCT）对下颌前磨牙髓腔三维重建的精度。方法:选取32颗单根下颌前磨牙,分别采用显微CT(micro-CT)和CBCT进行扫描,对髓腔进行三维重建,分别提取髓腔的三维表面模型和三维体积模型。在Amira 5.0软件中对髓腔表面模型配准后,以micro-CT重建的髓腔模型为参考,检测CBCT重建模型和其相比的形态差异,进行色阶图颜色标示,记录整体形态的三维偏差值并分析2种扫描图像对髓腔体积重建的测量值差异。采用SPSS 13.0软件包对数据进行统计学分析。结果:32颗牙的三维形态偏差RSM值平均为0.27 mm,最大的形态差异分布于髓腔的根尖段和一些细小的解剖变异结构。Micro-CT和CBCT重建髓腔模型的体积测量值分别为(34.89±4.36) mm3和(27.32±4.83) mm3, 差异具有显著性（P<0.05）。结论:利用CBCT扫描图像对下颌前磨牙髓腔进行三维重建时,存在着一定程度的结构丢失,且多位于根尖段和细小的解剖变异部位。口腔临床医师在利用CBCT辅助诊疗时,应考虑到以上特点。

关键词: 锥体束CT, 显微CT, 下颌前磨牙, 髓腔, 三维重建, 形态差异, 体积测量

Abstract: PURPOSE: To analyze the accuracy of 3D reconstruction of pulp cavity in mandibular premolars based on cone-beam CT (CBCT). METHODS: Thirty-two extracted single-rooted mandibular premolars were randomly collected and scanned by micro-CT and CBCT. After image segmentation and 3D reconstruction, the surface model and volume model of the pulp cavity were rendered. By using Amira 5.0 software, each pairs of pulp cavity surface models were registered. The surface models reconstructed from micro-CT scanning were set as the references and the surface models reconstructed from CBCT were tested. The morphological differences between each pairs of surface models were calculated by Amira 5.0 software and represented by color-coded maps. The total 3D morphological difference value of each sample was recorded and the volume reconstruction differences between the two image acquisition techniques were analyzed. Statistical analysis was performed with SPSS 13.0 software package. RESULTS: The mean value of 3D morphological differences of 32 teeth was 0.27 mm. Distribution of the greatest morphological differences were mainly located in the apical portion of the pulp cavity and some small anatomical variation. The volume of the reconstructed models by micro-CT and CBCT were (34.89±4.36) mm3 and (27.32±4.83) mm3 respectively, and the difference was significant (P<0.05). CONCLUSIONS: When CBCT scanning is used to reconstruct pulp cavity of mandibular premolars, there is certain degree of information loss, which mainly distributes in the apical portion and small anatomical variation sites. Dentists should consider these characteristics during clinical application of CBCT.

Key words: Cone-beam CT, Micro-CT, Mandibular premolars, Pulp cavity, 3D reconstruction, Morphological differences, Volume measurement

中图分类号:

R783.1

李骏, 潘乙怀, 赵瑜, 李玲. 锥形束CT对下颌前磨牙髓腔三维重建的精度分析[J]. 上海口腔医学, 2018, 27(2): 146-149.

LI Jun, PAN Yi-huai, ZHAO Yu, LI Ling. Accuracy of 3D reconstruction of pulp cavity in mandibular premolars based on cone-beam CT[J]. Shanghai Journal of Stomatology, 2018, 27(2): 146-149.

参考文献

[1] Vertucci FJ.Root canal anatomy of the human permanent teeth[J]. Oral Surg Oral Med Oral Pathol, 1984, 58(5): 589-599.
[2] Cotton TP, Geisler TM, Holden DT, et al.Endodontic application of cone-beam volumetric tomography[J]. J Endod, 2007, 33(9): 1121-1132.
[3] De Vos W, Casselman J, Swennen GR.Cone-beam computerized tomography (CBCT) imaging of the oral and maxillofacial region: a systematic review of the literature[J]. Int J Oral Maxillofac Surg, 2009, 38(6): 609-625.
[4] Estrela C, Bueno MR, Leles CR, et al.Accuracy of cone beam computed tomography and panoramic and periapical radiography for detection of apical periodontitis[J]. J Endod, 2008, 34(3): 273-279.
[5] Dawood A, Patel S, Brown J.Cone beam CT in dental practice[J]. Br Dent J, 2009, 207(1): 23-28.
[6] Gantt DG, Kappleman J, Ketcham RA, et al.Three-dimensional reconstruction of enamel thickness and volume in humans and hominoids[J]. Eur J Oral Sci, 2006, 114(Suppl 1):360-364.
[7] Liu Y, Olszewski R, Alexandroni ES, et al.The validity of in vivo tooth volume determinations from cone-beam computed tomography[J]. Angle Orthod, 2010, 80(1):160-166.
[8] Blattner TC, Geogre N, Lee CC, et al.Efficacy of cone-beam computed tomography as a modality to accurately identify the presence of second mesiobuccal canals in maxillary first and second molars: a pilot study[J]. J Endod, 2010, 36(5): 867-870.
[9] Matherne RP, Angelopoulos C, Kulild JC, et al.Use of cone-beam computed tomography to identify root canal systems in vitro[J]. J Endod, 2008, 34(1): 87-89.
[10] Maret D, Molinier F, Braga J, et al.Accuracy of 3D reconstructions based on cone beam computed tomography[J]. J Dent Res, 2010, 89(12): 1465-1469.
[11] Besl PJ, McKay ND. A method for registration of 3-D shapes[J]. IEEE Trans Pattern Anal Mach Intell, 1992, 14(2): 239-256.
[12] Kamburoglu K, Onder B, Murat S, et al.Radiographic detection of artificially created horizontal root fracture using different cone beam CT units with small fields of view[J]. Dentomaxillofac Radiol, 2013, 42(4): 20120261.
[13] Hatcher DC.Operational principles for cone-beam computed tomography[J]. J Am Dent Assoc, 2010, 141(Suppl 3): 3S-6S.
[14] Hassan BA, Payam J, Juyanda B, et al.Influence of scan setting selections on root canal visibility with cone beam CT[J]. Dentomaxillofac Radiol, 2012, 41(8): 645-648.
[15] Maret D, Telmon N, Peters OA, et al.Effect of voxel size on the accuracy of 3D reconstructions with cone beam CT[J]. Dentomaxillofac Radiol, 2012, 41(8): 649-655.
[16] Kato A, Ohno N.Construction of three-dimensional tooth model by micro-computed tomography and application for data sharing[J]. Clin Oral Investig, 2009, 13(1): 43-46.
[17] Peters OA, Laib A, Ruegsegger P, et al.Three-dimensional analysis of root canal geometry by high-resolution computed tomography[J]. J Dent Res, 2000, 79(6): 1405-1409.
[18] Rhodes JS, Ford TR, Lynch JA, et al.Miro-computed tomography: a new tool for experimental endodontology[J]. Int Endod J, 1999, 32(3): 165-170.
[19] Sousa TO, Hassan B, Mirmohammadi H, et al.Feasibility of cone-beam computed tomography in detecting lateral canals before and after root canal treatment: an ex vivo study[J]. J Endod, 2017, 43(6): 1014-1017.

锥形束CT对下颌前磨牙髓腔三维重建的精度分析

Accuracy of 3D reconstruction of pulp cavity in mandibular premolars based on cone-beam CT

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 13

编辑推荐

Metrics

本文评价

[1]	唐汝萍, 刘帅, 赵震锦, 汪俊妍. 骨性Ⅲ类下颌偏斜患者颞下颌关节形态位置及上颌骨特征的三维评估[J]. 上海口腔医学, 2023, 32(1): 91-96.
[2]	高琳, 韩祥永, 徐晓明. 不同材料及不同固位深度的髓腔固位冠修复下颌第二磨牙的三维有限元分析[J]. 上海口腔医学, 2022, 31(6): 621-624.
[3]	林翔, 傅裕杰, 任根强, 温佳欢, 陈宇飞, 张旗. U-Net神经网络分割锥形束CT影像中下颌磨牙牙体与牙髓腔及其准确性验证[J]. 上海口腔医学, 2022, 31(5): 454-459.
[4]	李怀奇, 叶金海, 王晨星, 朱载瓯, 武和明. 三维重建下3D打印技术在下颌骨缺损修复中的应用评价[J]. 上海口腔医学, 2021, 30(3): 283-287.
[5]	王玉俏, 迟敬文, 刘轶凡, 冯枫, 吴慧, 刘文. 成人不同垂直骨面型颧牙槽嵴区骨皮质密度分析[J]. 上海口腔医学, 2019, 28(6): 652-656.
[6]	吴雨桐, 孙健, 李亚莉, 陈立强, 陈晨, 邓楠, 李莉, 王志浩. 骨性Ⅲ类错正颌手术前、后面部软、硬组织变化比率的三维研究[J]. 上海口腔医学, 2019, 28(2): 158-164.
[7]	夏松，戴红卫，张翼，王超，邱靓星，王华桥. 高位头帽-口外弓肌激动器治疗Ⅱ类高角儿童患者前、后的上气道变化[J]. 上海口腔医学, 2018, 27(3): 270-274.
[8]	孙楚文, 刘宇, 杨一鸣, 廖骞. 多根管下颌第一前磨牙根管形态的显微CT分析[J]. 上海口腔医学, 2018, 27(1): 6-10.
[9]	冯耀浦, 乔敏, 周洪, 张艳宁, 司新芹. 基于二维DR的颅面硬组织与软组织拟合的研究[J]. 上海口腔医学, 2017, 26(1): 59-63.
[10]	冯耀浦，周洪，翟培芳，张艳宁，孙琳琳. 基于二维DR数据的颅面硬组织三维重建精度分析[J]. 上海口腔医学, 2016, 25(2): 181-186.
[11]	郭雪华, 姜茜, 阮宏, 罗英, 余优成. DBBM骨替代材料在上颌窦外提升中的三维影像学研究[J]. 上海口腔医学, 2013, 22(4): 448-452.
[12]	李骏;李玲. 下颌第一前磨牙C形牙根根管横断面形态及壁厚的锥体束CT分析 [J]. 上海口腔医学, 2012, 21(5): 531-534.
[13]	张勇;杨育生;吴忆来;梁赟;王国民. 牙槽突裂植骨吸收率的测量分析 [J]. 上海口腔医学, 2012, 21(3): 308-311.