不同肩台宽度的下前牙全瓷联冠的有限元分析

上海口腔医学 ›› 2014, Vol. 23 ›› Issue (2): 160-165.

不同肩台宽度的下前牙全瓷联冠的有限元分析

欧阳少波¹, 王军², 张洪斌¹, 廖岚¹*, 朱洪水¹*

1.南昌大学附属口腔医院修复科, 江西南昌 330006;
2.南昌大学第二附属医院口腔科, 江西南昌 330006

收稿日期:2013-07-09 出版日期:2014-04-20 发布日期:2014-05-21
通讯作者: 廖岚, Tel:0791-86350706, E-mail:Liaolan5106@163.com;朱洪水, Tel:0791-86360817, E-mail:zhuhongshui@126.com
作者简介:欧阳少波(1983-), 男, 硕士研究生, E-mail:ouyang5666845@126.com
基金资助:
江西省教育厅项目(GJJ09130)

Finite element stress analysis of all-ceramic continuous crowns of the lower anterior teeth in differential shoulder thickness

OUYANG Shao-bo¹, WANG Jun², ZHANG Hong-bin¹, LIAO Lan¹, ZHU Hong-shui¹

1.Department of Prosthodontics, Affiliated Stomatological Hospital of Nanchang University. Nanchang 330006;
2.Department of Oral Surgery, The Second Affiliated Hospital of Nanchang University. Nanchang 330006, Jiangxi Province, China

Received:2013-07-09 Online:2014-04-20 Published:2014-05-21

摘要/Abstract

摘要： 目的: 采取有限元分析研究肩台宽度变化对3种不同全瓷材料的下颌中切牙联冠修复的影响。方法: 利用下颌中切牙全瓷联冠的三维有限元模型, 对3种不同全瓷材料以及肩台宽度变化的全瓷联冠进行垂直向和唇向45°大面积加载120 N, 并采用Abaqus 6.11软件包对数据进行力学分析。结果: 利用CBCT、Mimics10.01软件及Abaqus 6.11软件建立了下颌中切牙全瓷联冠、基牙、牙周膜和牙槽骨的三维有限元模型。不同全瓷材料和肩台宽度对牙周膜、牙槽骨的等效应力峰值几乎无影响。同一肩台宽度下, 大面积加载120 N时, 3种全瓷联冠中冠受到的拉应力最大为In-Ceram Alumina, 其次为In-Ceram Zirconia, 最小为IPS.Empress2。唇向45°大面积加载120 N时, IPS.Empress2随着肩台宽度增加, 冠边缘的最大拉应力值上升。结论: 建立的三维有限元模型具有很好的几何相似度, 在所设定的条件范围内, 全瓷材料的弹性模量越大, 联冠受到的拉应力也越大。

关键词: 有限元分析, 全瓷联冠, 应力分布, 三维有限元模型

Abstract: PURPOSE:To investigate the stress distributions under load in 3 types of all-ceramic continuous crowns of the lower anterior teeth with differential shoulder thickness. METHODS: Cone-beam CT (CBCT) was used to scan the in vitro mandibular central incisors, and achieve three-dimensional finite element model of all-ceramic continuous crowns with different shoulder width by using Mimics, Abaqus software. Different load conditions were simulated based on this model to study the effect of shoulder width variation on finite element analysis of 3 kinds of different all-ceramic materials of incisors fixed continuous crowns of the mandibular. RESULTS: Using CBCT, Mimics10.01 software and Abaqus 6.11 software, three-dimensional finite element model of all-ceramic continuous crowns of the mandibular incisor, abutment, periodontal ligament and alveolar bone was established. Different ceramic materials and various shoulder width had minor no impact on the equivalent stress peak of periodontal membrane, as well as alveolar bone. With the same shoulder width and large area of vertical loading of 120 N, the tensile stress was the largest in In-Ceram Alumina, followed by In-Ceram Zirconia and the minimum was IPS.Empress II. Under large area loading of 120 N 45° labially, when the material was IPS.Empress II, with the shoulder width increased, the porcelain plate edge of the maximum tensile stress value increased, while the other 2 materials had no obvious change. CONCLUSIONS:Finite element model has good geometric similarity. In the setting range of this study, when the elastic modulus of ceramic materials is bigger, the tensile stress of the continuous crown is larger.

Key words: Finite element analysis, All-ceramic continuous crowns, Stress distribution, 3-dimensional finite element model

中图分类号:

R783

欧阳少波, 王军, 张洪斌, 廖岚, 朱洪水. 不同肩台宽度的下前牙全瓷联冠的有限元分析[J]. 上海口腔医学, 2014, 23(2): 160-165.

OUYANG Shao-bo, WANG Jun, ZHANG Hong-bin, LIAO Lan, ZHU Hong-shui. Finite element stress analysis of all-ceramic continuous crowns of the lower anterior teeth in differential shoulder thickness[J]. Shanghai Journal of Stomatology, 2014, 23(2): 160-165.

参考文献

[1] Burke FJ, Fleming GJ, Nathanson D, et al. Are adhesive technologies needed to support ceramics? An assessment of the current evidence [J]. J Adhes Dent, 2002, 4(1): 7-22.
[2] Rekow ED, Harsono M, Janal M, et al. Factorial analysis of variables influencing stress in all- ceramic crowns [J]. Dent Mater, 2006, 22(2): 125-132.
[3] Liu B, Lu C, Wu Y, et al. The effects of adhesive type and thickness on stress distribution in molars restored with all-ceramic crowns [J]. J Prosthodont, 2011, 20(1): 35-44.
[4] 王惠芸. 我国人牙的测量和统计[J].中华口腔科杂志, 1959, 7(3): 149 -151.
[5] Fischer H, Weber M, Marx R. Lifetime prediction of all-ceramic bridges by computational methods[J].J Dent Res, 2003, 82(3):238-242.
[6] Imanishi A, Nakamura T, Ohyama T, et al. 3-D Finite element analysis of all-ceramic posterior crowns [J]. J Oral Rehabil, 2003, 30(8): 818-822.
[7] Rekow ED, Harsono M, Janal M, et al. Factorial analysis of variables influencing stress in all-ceramic crowns[J]. Dent Mater, 2006, 22(2): 125-132.
[8] 皮昕. 口腔解剖生理学[M]. 第5版. 北京: 人民卫生出版社, 2004: 250-257.
[9] Rafferty BT, Janal MN, Zavanelli RA, et al. Design features of a three-dimensional molar crown and related maximum principal stress. A finite element model study[J]. Dent Mater, 2010, 26(2): 156-163.
[10] Imanishi A, Nakamura T, Ohyama T, et al. Mechanical properties of various new Ceramic materials [J]. Japan J Esthe Dent, 2001, 13(1): 18-21.
[11] 李智勇, 李雅琼, 潘新华, 等. 不同全瓷材料修复种植体支持单冠的应力分析 [J]. 武汉理工大学学报, 2010, 32(23): 27-30.
[12] 徐平. 下颌后牙三单位全瓷固定桥不同连接体设计的三维有限元分析 [D].西安：第四军医大学, 2008.
[13] Lawn BR, Pajares A, Zhang Y, et al. Materials design in the performance of all-ceramic crowns[J]. Biomaterials, 2004, 25(14): 2885-2892.
[14] 王卫国, 张少锋, 陈建军, 等. 面厚度与肩台宽度连续变化的下颌第一磨牙全瓷冠三维有限元分析 [J]. 中华口腔医学杂志, 2011, 46(4): 205-209.

[1]	毛懿, 陈旭卓, 覃海艺, 甄锦泽, 邱亚汀, 霍亮, 张善勇. 双侧冠突切除对肋骨-肋软骨移植重建颞下颌关节受力影响的有限元分析[J]. 上海口腔医学, 2022, 31(2): 126-131.
[2]	高远, 陈杰, 王高琦, 李云凯, 卞翠荣. 种植体-基台连接设计对基台与基台螺丝受力影响的三维有限元分析[J]. 上海口腔医学, 2021, 30(5): 481-487.
[3]	邱晓键, 肖善社, 谷雪莲, 朱来宽, 蒋倩. 不同锥度根管锉对根管壁抗折强度的影响[J]. 上海口腔医学, 2020, 29(5): 471-475.
[4]	左书玉, 王璇, 吴海威, 张东升. 不同种植体外形设计对上颌窦提升术后种植体周围应力分布的影响[J]. 上海口腔医学, 2020, 29(4): 355-358.
[5]	韩婧, 解东平, 王慧珊, 周子疌, 刘剑楠. 微型钛板与生物可吸收板在下颌骨骨切开术固定中的应力比较[J]. 上海口腔医学, 2020, 29(3): 237-241.
[6]	王诗哲, 潘晓岗, 周可拓. 拔牙病例隐形矫治器设计的有限元分析[J]. 上海口腔医学, 2019, 28(3): 264-267.
[7]	朱远兵, 赖光云, 汪俊. 外力方向对防护牙托性能影响的有限元分析[J]. 上海口腔医学, 2018, 27(6): 574-578.
[8]	顾美珍, 徐宏鸣, 陈芳, 李晓艳, 蒋钰钢, 李克勇. 不完全腭裂咽腔三维有限元模型的建立[J]. 上海口腔医学, 2018, 27(6): 591-595.
[9]	何淞，陈周艳，杨四维，黄跃. 唇舌侧弓丝力学性能差异的三维有限元分析[J]. 上海口腔医学, 2015, 24(6): 660-666.
[10]	董晶,张哲湛,周国良. 上颌第一磨牙远中移动时牙周膜应力分布的非线性三维有限元分析[J]. 上海口腔医学, 2015, 24(3): 315-320.
[11]	韩丽会,邱晓霞,邢旭娜,蔡留意. 上颌前牙区种植方案中角度设计的三维有限元分析[J]. 上海口腔医学, 2015, 24(2): 157-163.
[12]	张珑,逯宜,杨柏松,郭妍,李芳萍. 不同大小MO洞型复合树脂嵌体修复应力分布的有限元分析[J]. 上海口腔医学, 2015, 24(2): 170-176.
[13]	赵莉, 李丽君, 赵克, 邓旭亮. 不同桩核系统修复上颌第一磨牙的有限元分析[J]. 上海口腔医学, 2013, 22(6): 607-612.
[14]	王晖, 吴建勇, 周铨, 刘剑. 不同牙槽骨高度的磨牙压低时牙周膜应力分析[J]. 上海口腔医学, 2013, 22(3): 247-251.
[15]	陈铮晰;潘晓岗;陈振琦. 上颌前牵引联合扩弓对唇腭裂植骨患者上颌骨影响的有限元分析 [J]. 上海口腔医学, 2012, 21(3): 287-293.